粉体行业在线展览
THF
面议
皖氟龙
THF
5412
--
化工,医药,制酸,氢氟酸,易燃,易爆,易挥发,高危行业
化工,医药,制酸,氢氟酸,易燃,易爆,易挥发,高危行业
名称: | THF氟塑料合金离心泵/ IHF氟塑料离心泵/衬氟离心泵/氟合金离心泵/化工离心泵/耐酸泵/盐酸泵/硫酸泵 |
输送介质: | 硫酸,盐酸,氢氟酸,王水,溴化物,强腐蚀酸性介质 |
适用行业: | 化工,医药,制酸,氢氟酸,易燃,易爆,易挥发,高危行业 |
产品特点: | 耐酸性 |
结构形式: | 卧式、泵与电机联轴器连接 |
口径: | 25~250mm |
流量: | 1.5~600m3/h |
扬程: | 5~80m |
转速: | 1450/2900r/min |
工作温度: | -20~+120℃ |
压力等级: | 1.6Mpa |
功率: | 1.1~132KW |
材料: | 衬氟,氟合金,PTFE,PFA |
一、产品简介:
产品概述:
衬氟离心泵第三代改良产品,是按国际标准并结合非金属泵的工艺设计制造,适用于长期输送任意浓度的强酸、碱、盐、强氧化剂等多种腐蚀性介质,其壳体采用金属外壳内衬聚全氟乙丙烯(FEP)及过流部件全部用塑料合金(PTFE、FEP)制成,集多种塑料泵之优点,具有耐腐蚀性强、耐磨性好、机械强度高、不老化、无毒素分解特点。在结构设计上,加粗了轴径、缩短了悬臂比,消除了化工泵的弊病,提高了运行稳定性,降低了维修费用和运行成本,泵的进出口均采用铸钢体加固,以增强了泵的耐压性。该泵具有耐腐、耐磨、耐高温、不氧化、机械强度高、运转平稳、结构先进合理、密封性能严格可靠、拆卸检修方便、使用寿命长等优点。
产品优点:
1.THF衬氟离心泵是按国际标准并结合非金属泵的工艺设计制造,具有耐腐、耐高温、不老化、机械强度高、高效节能等优点。
2.泵体、叶轮和泵盖采用CFD计算机流体力学设计水力部件进行模块设计和模压烧结而成。具有流道宽、效率高、汽蚀余量性能好、径向力小、尺寸准确、流道光洁和互换性好等特点;
3.氟塑料(PTFE、FEP、PFA)是当今世界**秀耐腐蚀材料(俗称:塑料王),可输送任意浓(强)度的酸、碱、氧化剂等腐蚀性介质而毫不受损;
4.轴封选用先进的外装式波纹管机械密封,不用拆卸即可调整机封,对磨的密封面可选配:碳化硅、无压烧结碳化硅、陶瓷、四氟、硬质合金等材料,以达到输送各种介质的要求,保证了机封的使用寿命。
5.无需独立润滑和冷却水,降低了能耗。
6.分为长支架轴联式和短支架直联式两种结构形式,无需拆卸管道,维修方便。
7.卧式安装,结构紧凑、国际标准设计,可与标准化工离心泵互换,方便用户更换和使用;
产品用途:
广泛应用于石油、化工、制酸、制碱、冶炼、稀土、农药、染料、医药、造纸、电镀、电解、酸洗、无线电、化成箔、科研机构、国防工业等生产流程中输送腐蚀性液体,尤其适用于强酸碱、有机容剂和贵重液体的输送。
性能范围:设计压力:1.6Mpa、流量:2-1400m3/h、扬程:3-125m、功率:0.55-400kw
适用温度: -20~120℃,采用新型材料耐温可达180℃;
注意事项:当介质比重大于1.3mg/cm3时订货时应说明,禁止空运转,禁止输送含有颗粒或有结晶的介质。
二、解剖图:
三、结构图:
四、性能曲线图:
五、性能参数表:
型号 | 转速r/min | 流量 m3/h | 扬程 m | 效率 % | 汽蚀余量 m | 进口X出口 mm | 电机功率 | 整机质量 |
THF25-20-125 | 2900 | 2 | 20.5 | 25 | 2.5 | 25×20 | 1.1 | 75 |
3.2 | 20 | 32 | 2.5 | |||||
5.5 | 18 | 46 | 2.5 | |||||
1450 | 0.75 | 5.4 | 15 | 2.5 | 0.37 | 55 | ||
1 | 5 | 17 | 2.5 | |||||
1.6 | 4.6 | 21 | 3 | |||||
THF25-20-160 | 2900 | 1.5 | 34.3 | 19 | 2.5 | 25×20 | 1.5 | 80 |
2 | 32 | 22 | 2.5 | |||||
3.2 | 29.6 | 25 | 3 | |||||
1450 | 0.75 | 8.5 | 16 | 2.5 | 0.37 | 55 | ||
1 | 8 | 18 | 2.5 | |||||
1.6 | 7.5 | 24 | 3 | |||||
THF25-20-200A | 2900 | 1.5 | 42 | 28 | 2.5 | 25×20 | 3 | 124 |
2 | 40 | 32 | 2.5 | |||||
3.2 | 38 | 30 | 3 | |||||
1450 | 0.75 | 10.5 | 15 | 2.5 | 0.55 | 90 | ||
1 | 10 | 18 | 2.5 | |||||
1.6 | 9.5 | 24 | 3 | |||||
THF25-20-200 | 2900 | 1.5 | 52.5 | 18 | 2.5 | 25×20 | 4 | 124 |
2 | 50 | 20 | 2.5 | |||||
3.2 | 48 | 22 | 3 | |||||
1450 | 0.75 | 13.1 | 15 | 2.5 | 0.75 | 90 | ||
1 | 12.5 | 18 | 2.5 | |||||
1.6 | 12 | 24 | 3 | |||||
THF25-20-250A | 2900 | 1.5 | 62 | 26 | 2.5 | 25×20 | 7.5 | 225 |
2 | 60 | 30 | 2.5 | |||||
3.2 | 58 | 28 | 3 | |||||
1450 | 0.75 | 15.5 | 15 | 2.5 | 1.5 | 118 | ||
1 | 15 | 18 | 2.5 | |||||
1.6 | 14.5 | 24 | 3 | |||||
THF25-20-250B | 2900 | 1.5 | 72 | 26 | 2.5 | 25×20 | 5.5 | 225 |
2 | 70 | 30 | 2.5 | |||||
3.2 | 68 | 28 | 3 | |||||
1450 | 0.75 | 18 | 15 | 2.5 | 1.1 | 118 | ||
1 | 17.5 | 18 | 2.5 | |||||
1.6 | 17 | 24 | 3 | |||||
THF25-20-250 | 2900 | 2 | 80 | 12 | 2.5 | 25×20 | 7.5 | 225 |
3.6 | 80 | 18 | 2.5 | |||||
5.5 | 78.5 | 26 | 3 | |||||
1450 | 0.75 | 20.5 | 11 | 2.5 | 1.5 | 118 | ||
1 | 20 | 16 | 2.5 | |||||
1.6 | 19.5 | 24 | 3 | |||||
THF32-20-125 | 2900 | 2 | 22 | 25 | 2.5 | 32×20 | 1.5 | 75 |
3.2 | 20 | 32 | 2.5 | |||||
5.5 | 18.5 | 46 | 3 | |||||
1450 | 1 | 5.4 | 24 | 2.5 | 0.55 | 45 | ||
1.6 | 5 | 22 | 2.5 | |||||
2.75 | 4.6 | 22.5 | 3 | |||||
THF32-20-160 | 2900 | 2 | 34.3 | 25 | 2.5 | 32×20 | 2.2 | 98 |
3.2 | 32 | 24 | 2.5 | |||||
5.5 | 29.6 | 21.5 | 3 | |||||
1450 | 1 | 8.5 | 18 | 2.5 | 0.55 | 55 | ||
1.6 | 8 | 22 | 2.5 | |||||
2.75 | 7.5 | 24.5 | 3 | |||||
THF32-20-200A | 2900 | 2 | 42 | 32 | 2.5 | 32×20 | 4 | 140 |
3.2 | 40 | 36 | 2.5 | |||||
5.5 | 38 | 34 | 3 | |||||
1450 | 1 | 10.5 | 25 | 2.5 | 0.75 | 78 | ||
1.6 | 10 | 28 | 2.5 | |||||
2.75 | 9.5 | 26 | 3 | |||||
THF32-20-200 | 2900 | 2 | 52.5 | 22 | 2.5 | 32×20 | 4 | 140 |
3.2 | 50 | 26 | 2.5 | |||||
5.5 | 48 | 28.5 | 3 | |||||
1450 | 1 | 13.1 | 15 | 2.5 | 0.75 | 78 | ||
1.6 | 12.5 | 18 | 2.5 | |||||
2.75 | 12 | 19.5 | 3 | |||||
THF32-20-250A | 2900 | 2 | 62 | 26 | 2.5 | 32×20 | 7.5 | 160 |
3.2 | 60 | 30 | 2.5 | |||||
5.5 | 58 | 28 | 3 | |||||
1450 | 1 | 15.5 | 15 | 2.5 | 1.1 | 98 | ||
1.6 | 15 | 18 | 2.5 | |||||
2.75 | 14.5 | 24 | 3 | |||||
THF32-20-250B | 2900 | 2 | 72 | 26 | 2.5 | 32×20 | 7.5 | 160 |
3.2 | 70 | 30 | 2.5 | |||||
5.5 | 68 | 28 | 3 | |||||
1450 | 1 | 18 | 15 | 2.5 | 1.1 | 98 | ||
1.6 | 17.5 | 18 | 2.5 | |||||
2.75 | 17 | 24 | 3 | |||||
THF32-20-250 | 2900 | 2 | 82 | 16 | 2.5 | 32×20 | 11 | 160 |
3.2 | 80 | 20 | 2.5 | |||||
5.5 | 78.5 | 23 | 3 | |||||
1450 | 1 | 20.5 | 15 | 2.5 | 1.5 | 98 | ||
1.6 | 20 | 18 | 2.5 | |||||
2.75 | 19.5 | 24 | 3 | |||||
THF40-25-125 | 2900 | 6.3 | 22 | 30 | 2.5 | 40×25 | 2.2 | 75 |
8 | 32 | 31 | 2.5 | |||||
10 | 30 | 32 | 3 | |||||
1450 | 2.2 | 5.4 | 26 | 2.5 | 0.55 | 42 | ||
3.2 | 5 | 28 | 2.5 | |||||
4.2 | 4.6 | 32 | 3 | |||||
THF40-25-160 | 2900 | 6.3 | 32 | 30 | 2.5 | 40×25 | 3 | 124 |
8 | 32 | 31 | 2.5 | |||||
10 | 30 | 32 | 3 | |||||
1450 | 2.2 | 8.5 | 23 | 2.5 | 0.55 | 78 | ||
3.2 | 8 | 25 | 2.5 | |||||
4.2 | 7.5 | 28 | 3 | |||||
THF40-25-200A | 2900 | 4.4 | 42 | 26 | 2.5 | 40×25 | 4 | 170 |
6.3 | 40 | 33 | 2.5 | |||||
8.3 | 38 | 32 | 3 | |||||
1450 | 2.2 | 10.5 | 25 | 2.5 | 0.55 | 102 | ||
3.2 | 10 | 28 | 2.5 | |||||
4.2 | 9.5 | 26 | 3 | |||||
THF40-25-200 | 2900 | 6.3 | 52.5 | 20 | 2.5 | 40×25 | 5.5 | 170 |
8 | 50 | 23 | 2.5 | |||||
10 | 48 | 30 | 3 | |||||
1450 | 2.2 | 13.1 | 25 | 2.5 | 1.1 | 102 | ||
3.2 | 12.5 | 28 | 2.5 | |||||
4.2 | 12 | 26 | 3 | |||||
THF40-25-250A | 2900 | 4.4 | 62 | 24 | 2.5 | 40×25 | 7.5 | 255 |
6.3 | 60 | 28 | 2.5 | |||||
8.3 | 58 | 28 | 3 | |||||
1450 | 2.2 | 15.5 | 20 | 2.5 | 1.1 | 155 | ||
3.2 | 15 | 24 | 2.5 | |||||
4.2 | 14.5 | 22 | 3 | |||||
THF40-25-250B | 2900 | 4.4 | 72 | 24 | 2.5 | 40×25 | 11 | 255 |
6.3 | 70 | 28 | 2.5 | |||||
8.3 | 68 | 28 | 3 | |||||
1450 | 2.2 | 18 | 20 | 2.5 | 1.5 | 155 | ||
3.2 | 17.5 | 24 | 2.5 | |||||
4.2 | 17 | 22 | 3 | |||||
THF40-25-250 | 2900 | 4.4 | 82 | 24 | 2.5 | 40×25 | 11 | 255 |
6.3 | 80 | 28 | 2.5 | |||||
8.3 | 78.5 | 28 | 3 | |||||
1450 | 2.2 | 20.5 | 20 | 2.5 | 1.5 | 155 | ||
3.2 | 20 | 24 | 2.5 | |||||
4.2 | 19.5 | 22 | 3 | |||||
THF50-32-125 | 2900 | 7.5 | 22 | 43 | 2 | 50×32 | 3 | 110 |
12.5 | 20 | 51 | 2 | |||||
15 | 18.5 | 49 | 2.5 | |||||
1450 | 3.75 | 5.4 | 40 | 2 | 0.55 | 55 | ||
6.3 | 5 | 45 | 2 | |||||
7.5 | 4.6 | 42 | 2.5 | |||||
THF50-32-160 | 2900 | 7.5 | 34.3 | 35 | 2 | 50×32 | 4 | 135 |
12.5 | 32 | 47 | 2 | |||||
15 | 29.6 | 47 | 2.5 | |||||
1450 | 3.72 | 8.5 | 30 | 2 | 0.55 | 68 | ||
6.3 | 8 | 40 | 2 | |||||
7.5 | 7.5 | 40 | 2.5 | |||||
THF50-32-200A | 2900 | 7.5 | 42 | 28 | 2 | 50×32 | 5.5 | 180 |
12.5 | 40 | 39 | 2 | |||||
15 | 38 | 43 | 2.5 | |||||
1450 | 3.7 | 10.5 | 23 | 2 | 0.75 | 170 | ||
6.3 | 10 | 33 | 2 | |||||
7.5 | 9.5 | 36 | 2.5 | |||||
THF50-32-200 | 2900 | 7.5 | 52.5 | 28 | 2 | 50×32 | 7.5 | 180 |
12.5 | 50 | 40 | 2 | |||||
15 | 48 | 48 | 2.5 | |||||
1450 | 3.7 | 13.1 | 22 | 2 | 1.1 | 170 | ||
6.3 | 12.5 | 33 | 2 | |||||
7.5 | 12 | 40 | 2.5 | |||||
THF50-32-250A | 2900 | 7.5 | 62 | 23 | 2 | 50×32 | 7.5 | 255 |
12.5 | 60 | 33 | 2 | |||||
15 | 58 | 36.5 | 2.5 | |||||
1450 | 3.75 | 15.5 | 17 | 2 | 1.1 | 155 | ||
6.3 | 15 | 27 | 2 | |||||
7.5 | 14.5 | 31 | 2.5 | |||||
THF50-32-250B | 2900 | 7.5 | 72 | 23 | 2 | 50×32 | 15 | 255 |
12.5 | 70 | 33 | 2 | |||||
15 | 68 | 36.5 | 2.5 | |||||
1450 | 3.75 | 18 | 17 | 2 | 2.2 | 155 | ||
6.3 | 17.5 | 27 | 2 | |||||
7.5 | 17 | 31 | 2.5 | |||||
THF50-32-250 | 2900 | 7.5 | 82 | 23 | 2 | 50×32 | 18.5 | 255 |
12.5 | 80 | 33 | 2 | |||||
15 | 78.5 | 36.5 | 2.5 | |||||
1450 | 3.75 | 20.5 | 17 | 2 | 2.2 | 155 | ||
6.3 | 20 | 30 | 2 | |||||
7.5 | 19.5 | 33 | 2.5 | |||||
THF65-50-125 | 2900 | 15 | 21.8 | 46 | 2 | 65×50 | 4 | 135 |
25 | 20 | 61 | 2 | |||||
30 | 18.5 | 67 | 2.5 | |||||
1450 | 7.5 | 5.35 | 46 | 2 | 0.55 | 75 | ||
12.5 | 5 | 61 | 2 | |||||
15 | 4.7 | 67 | 2.5 | |||||
THF65-50-160 | 2900 | 15 | 35 | 46 | 2 | 65×50 | 5.5 | 155 |
25 | 32 | 56 | 2 | |||||
30 | 30 | 65 | 2.5 | |||||
1450 | 7.5 | 8.8 | 40 | 2 | 1.1 | 145 | ||
12.5 | 8 | 51 | 2 | |||||
15 | 7.2 | 60 | 2.5 | |||||
THF65-40-200A | 2900 | 15 | 42 | 41 | 2 | 65×40 | 7.5 | 210 |
25 | 40 | 52 | 2 | |||||
30 | 38 | 53.5 | 2.5 | |||||
1450 | 7.5 | 10.5 | 35 | 2 | 1.5 | 132 | ||
12.5 | 10 | 46 | 2 | |||||
15 | 9.5 | 47.5 | 2.5 | |||||
THF65-40-200 | 2900 | 15 | 53 | 35 | 2 | 65×40 | 11 | 210 |
25 | 50 | 51 | 2 | |||||
30 | 47 | 48 | 2.5 | |||||
1450 | 7.5 | 13.2 | 30 | 2 | 1.5 | 132 | ||
12.5 | 12.5 | 46 | 2 | |||||
15 | 11.8 | 42 | 2.5 | |||||
THF65-40-250A | 2900 | 15 | 62 | 34 | 2 | 65×40 | 15 | 360 |
获取更多信息,请访安徽皖氟龙泵阀有限公司. 网站
安徽皖氟龙泵阀有限公司. 的其他产品
FLOW
管道泵
相关搜索
|